Installation of a washing machine in the kitchen. Dishwasher - how to build it into a finished kitchen yourself? Checking the correct installation and connection

In the article we will tell you how to choose the right place to install the dishwasher, in what order to connect it. After the dishwasher is delivered to your home, you can immediately connect and start it yourself, without overpaying for the services of a master.

How to install a dishwasher in the kitchen

There are two options for installing PMM: in a finished kitchen or in a pre-designated place in a kitchen set. Dishwashers vary in type and dimensions:

  • Compact. Holds 3 to 5 sets of dishes. Dimensions 50x60x50 cm. Mounted on the countertop or under the sink.

  • Narrow. Width 45 cm, capacity from 6 to 10 sets. It can be fully or partially built-in.

  • Full size. Dimensions 65x65x90 cm, holds from 10 to 15 sets of dishes. Can be built-in or freestanding.

Usually, manufacturers in any kitchen set provide a place to place appliances. For this, the dimensions of a narrow dishwasher are taken, 5-10 cm are added to them from all sides. If your kit does not have a special cabinet, then it is better to choose a freestanding machine. You can install it in any convenient place, even between the cabinets.

When choosing a free-standing PMM, you need to take into account that the appearance of the case is combined with the design of the kitchen.

If you have prepared drawings in advance for placing a Samsung, Miele or other brand dishwasher, there will be no installation problems. Otherwise, for embedding, pick up a cabinet near the sink. Keep in mind that the distance from the PMM case to the back wall must be at least 5 cm for normal ventilation.

If you have a small family, and the area of ​​\u200b\u200bthe kitchen does not allow you to install a full-sized model, choose the desktop version. You can put it under the sink, and the connection rules do not differ from other models.

  • Before buying built-in appliances, measure the dimensions of the kitchen cabinet.
  • Dishwasher legs can be adjusted in height. Use a level to level the machine. Some Hotpoint Ariston, Whirlpool models are very sensitive to tilt even as low as 2 degrees. This may affect their future work.
  • Mount the machine near a sink. This will make it easier to connect the drain and water without having to extend the hoses. Experts say that lengthening the hoses can lead to leakage, as well as create a large load on the drain pump.

  • When building into furniture, install a metal plate under the countertop to protect the wood from steam. In built-in models, the plate is included.

Take a look at the instruction manual. It shows the installation and installation of the dishwasher. Included are templates for hanging the door.

  • To connect the equipment to the network, a separate moisture-resistant socket is used. Do not connect with extension cords or tees.

Independent connection of the dishwasher

It is recommended to immediately install the machine on site, and then deal with the connection. But in the case of the built-in model, it is more convenient to first connect the hoses, and then mount the machine in a niche or cabinet. How to install an embedded PMM, read our separate article.

What you need to connect

Accessories:

  • euro socket with a moisture-resistant housing and grounding;
  • copper three-core cable (for organizing wiring);
  • stabilizer;
  • brass tee with stopcock;
  • clutch;
  • corner tap;
  • extension cord and additional hose;
  • siphon with two outlets (for connecting dishwasher and washing machine simultaneously);
  • hose "Aquastop" (if not available);
  • fum tape for sealing joints;
  • filter;
  • clamps, gaskets.

Tools:

  • pliers;
  • screwdriver;
  • wrench;
  • level.

Organization of electrical wiring

The dishwasher cord is specially made short. The European type plug can be connected to a special socket, which is located no higher than 45 cm from the floor.

Do-it-yourself replacement of the plug on the dishwasher will void the warranty.

How to organize the electrical connection correctly:

  1. Drill a channel in the wall, lay a copper wire.
  2. Arrange a moisture-resistant socket with grounding.
  3. Connect the outlet through a 16-amp difavtomat. For safety, it is recommended to install a voltage stabilizer. How to choose a dishwasher stabilizer, read in a separate article.

Plumbing work

You know how to install and connect the electrical part of the machine. Any model of PMM Korting, Hansa, Gorenje, Beko, Ikea, Ariston is connected to the water supply in the same way. by the most simple solution will be connected through a mixer. But if you install the equipment far from the sink, then the method of tapping into a cold water pipe is suitable.

To connect to a water pipe:

  1. Using a grinder, cut a piece of pipe.
  2. Install the release clutch.
  3. Screw a tap with a shut-off valve onto the coupling.
  4. Connect the dishwasher hose to the faucet outlet.

Through mixer:

  1. Disconnect the mixer hose from the pipe outlet.
  2. Install brass tee.
  3. Connect a mixer to one outlet.
  4. To the other - a coarse filter and the end of the inlet hose.

Now take care of the water.

Drainage work

Where to connect the drain? There are also two options to choose from here:

  • Directly to the sewer.
  • through the siphon.

To connect to the sewer, it is enough to install an adapter on the outlet, to which you can connect the drain hose of the dishwasher and washing machine. Connections are carefully sealed.

When installing through a siphon:

  • Remove the old and install a new siphon.
  • Connect the dishwasher drain hose to the outlet.
  • Be sure to fasten the connection with a clamp. With strong pressure, the hose can be torn from its place, which will lead to leakage.

Observe the correct spacing and bend of the hose when draining. This will help avoid the siphon effect (see diagram below).

As you can see, you can organize the installation of PMM "Hans", "Burning" and other brands yourself. When the work is finished, run the test program without dishes to check the strength of the connections and the operation of the nodes. How to run your dishwasher for the first time, read the article.

The video will help you install the dishwasher yourself:

In the article we will tell you how to connect the dishwasher with your own hands, what tools you will need for work. After all, before you pull out the shining dishes from the bunker, you need to properly install the equipment.

Independent organization of work

Dishwashers can be compact (desktop), built-in and freestanding. All stand-alone models (compact and full-size) connect in the same way. For built-in PMMs, the only difference is the installation method. The machine is placed in a cabinet or niche, additionally attached to the walls.

Has the equipment been delivered to your home? Shake the packaging lightly to find out the safety of the machine. There should be nothing to click, creak, roll.

When connecting dishwashers "Siemens", "Hans" (Hansa), "Indesit", first of all, look at the instructions. Consider a place for installation in the kitchen. If you did not provide a cabinet for appliances in the headset in advance, then choose a place near the sink.

You can start preparing tools and parts.

Tools and accessories

What you need to connect to the water supply and sewerage:

  1. A brass tee is considered the most reliable. It is desirable that a shut-off valve is attached to it. The faucet can be purchased separately.
  2. Siphon with two outlets to .
  3. Fum-tape for sealing joints.
  4. Clamps for strengthening the connected hoses.
  5. Gaskets.

From tools:

  • slotted and cross screwdrivers;
  • wrench;
  • wire cutters;
  • level.

To supply electricity:

  • moisture resistant socket;
  • Voltage regulator;
  • difavtomat.

To install the fasteners you will need a drill and bolts.

You also need to take into account some features of individual brands:

  1. Bosch has a sensitive inlet valve, so be sure to connect a flow filter.
  2. Siemens dishwashers are demanding on fixtures.
  3. "Electrolux" do not tolerate tilt to the side even a few degrees.

How is the PMM connected correctly? It is important to follow the sequence:

  • first, the connection is made to the drain;
  • then to the plumbing;
  • to the mains.

After that, a test run is carried out. Then the built-in appliances are installed in place.

Organization of the drain

Start by installing a siphon. To connect the dishwasher and washing machine together, connect a siphon with two outlets. Once everything is ready, connect the end of the hose and the spout of the siphon. Secure the connection with a clamp.

Do not forget:

  • Create a kink at the junction with the fitting. This will help you avoid returning. Wastewater back to the bunker.
  • Create a knee at the bottom that will help to avoid unpleasant odors.

Important! The length of the drain hose should not exceed 1.5-2 meters.

Working with plumbing

Decide which water supply your machine model is connected to. It can be only cold or both hot and cold water supply.

Work sequence:

  • Shut off the water supply.
  • Disconnect the mixer hose from the water supply.
  • Install a brass or bronze tee.
  • Connect a mixer to one outlet.
  • Install a flow filter on the other outlet, and then a dishwasher hose.
  • Seal the joints with a "fumka" by winding the tape 10-15 times along the thread.

Some users want to save electricity by doing. But this can be dangerous. In addition, the hot stream is supplied with rust impurities and small debris.

Models that are specially equipped to work with hot water supply have a special hose included. It is resistant to high temperatures.

Network connection

In old houses, wiring and sockets are not prepared for the use of powerful equipment. Want to extend the life of your dishwasher? Then organize the correct wiring. It is difficult to cope with such work on your own. It is better to contact a professional electrician.

What work needs to be done:

  • make a hole in the wall;
  • lay a three-core copper wire;
  • organize a moisture-resistant European-type socket with grounding;
  • make a connection through a difavtomat.

You need to be very careful when connecting the dishwasher and oven. Some .

Forbidden:

  1. Connect equipment through tees, carrying, extension cords.
  2. Position the socket above 45 cm from the floor.
  3. Connect the PMM plug to the same socket with the stove.

To connect the dishwasher, you need a couple of hours if you have everything you need. If you do not know how to connect a dishwasher with your own hands, then detailed instructions, a list of materials and tools are in front of you.

Dishwasher Connection Tools

You will need:

  1. Sewer siphon for drain connection.
  2. Shut-off ball valve that will shut off the water in front of the dishwasher.
  3. ¾" threaded brass tee fitting for water connection.
  4. The filter for rough cleaning of the given water.
  5. PVC pipe or hose high pressure for drain (if there is no siphon included).
  6. Pliers, screwdriver, tape, waterproofing tape FUM.

It is recommended to install a tee not steel or cast iron (they rust quickly), but bronze or brass, a ball valve - metal-plastic or from the same brass or bronze. So you will ensure long-term maintenance-free operation of components.

Dirty water is discharged through the siphon into the sewer, so it is better that it be universal - with several fittings so that it can be connected to the drain holes of other household appliances.

The siphon also traps unpleasant odors from the sewer, so don't skimp on it - no matter how much the kit costs, it's important that it works for a long time. Be sure to check the complete set of the siphon so as not to go once again for the missing gasket. The filter for water purification is used the same as in the water meter system.

The procedure for connecting the dishwasher

Dishwashing machines are desktop, built-in (compact) and stationary. Despite the difference in dimensions, the connection of all communications is carried out according to general principle with minor differences.

How to connect a dishwasher of any type - stationary, compact or built-in:

  1. Decide on the place where the dishwasher will be installed. Most often this is a working area next to the kitchen sink.
  2. Choose where you will connect the unit to the mains. It is safer if a separate grounded socket is installed, but this applies mainly to powerful devices.
  3. When installing a separate outlet, choose a wire with a cross section of 2.5 mm 2 and protection in the form of a 16 A machine. The best reliable option is to add a 30 mA RCD (residual current device).
  4. Choose a place to connect to cold water. But you may have a model with DHW connectivity, so you will need to connect the dishwasher to hot water.
  5. Water is connected with a special high pressure hose with a ¾ inch union nut. Therefore, a shut-off valve with a ¾ inch thread must be screwed into the tee.
  6. The dishwasher drain is connected to the internal sewerage, and it is better to organize the connection separately through a siphon tee (for example, on a kitchen sink drain).

Now about how to connect the drain of the dishwasher. Draining is the easiest thing to do. To do this, in each kitchen siphon there is a plug at the bottom that needs to be unscrewed, and screw the siphon onto this thread, and the hose for draining dirty water from the dishwasher will already be connected to it.

The standard drain hose is 1.5 meters long and should be enough. The siphon has a built-in valve to delay backflow and odors from the sewer, but one more protective measure can be provided - fix the drain hose so that a small half-ring forms below the siphon. It will be a kind of water valve.

Electrical connection

Not everyone knows how to properly connect the dishwasher to the network. The best option is a separate socket, a separate cable, grounding and separate protection in the form of an RCD and a circuit breaker. But this rule is for powerful units and work for professionals. We want to connect the device ourselves.

So, we connect the dishwasher ourselves. For a kitchen in which a compact machine, such as a Bosch, will be installed, the option of connecting to the nearest outlet is suitable. Moreover, the entire electrical network of the apartment is protected by not one, but two machines on the landing - one before the meter, and one after it.

For a low-power sink, you can buy a grounded socket plug and make an extension cord with your own hands. Such a grounding connection protects against the load on the home network, and the fact that all wiring wires are concreted into the walls protects them from overheating.

How to bring water

How to connect a bosch dishwasher or other model to water. The supply of cold water requires a tie-in to the water supply system, and this is not necessarily welding work. Just at the place where the water is connected to the cold tap in the kitchen, a tee is mounted, from which the hose is connected to the dishwasher.

Threaded connections must be sealed with FUM-tape (8-12 turns must be made). For a tight connection, hand effort is enough, without keys. Instead of FUM tape, you can use linen winding, tow or sealant.

Immediately screw the ball valve (valve) onto the tee, and connect a cold water hose to it. If your dishwasher model can be connected to hot water, then the essence of the process does not change - the tee cuts into the hot water supply pipe.

Features of connecting a portable machine

The desktop dishwasher is installed on the countertop, the drain is usually organized by the most in a simple way– Dirty water drains directly into the sink. Water is supplied to the compact dishwasher in the same way as in stationary models, and the power supply is from a conventional kitchen electrical outlet.

Standard dimensions of the built-in model: width 450-600 mm, unit depth - 550 mm, height - 820 mm. The built-in model is installed in two versions:

  1. In a specially designated place in the kitchen (like a washing machine or mini-refrigerator) under the countertop, taking into account the size of the future unit.
  2. As a separate cabinet, decorated to match the kitchen furniture. For this, special facades for dishwashers are sold, from which you can choose the right decor.

Connect the built-in dishwasher to water, sewerage and voltage in the same way as in the stationary version. And which model your dishwasher will belong to: built-in, portable or stationary - it depends only on the size of the kitchen room and your desire.

Features of connecting a stationary machine

You can find out how to connect the dishwasher yourself from the instructions for the appliance. All technological processes described in the instructions are accompanied by pictures and marked to follow the sequence of operations. Often, not everything is clear from the pictures, so use our advice.

The instruction may not contain the features of the process, how to connect the dishwasher to the sewer, drain and voltage exactly for your conditions, so you need to proceed from the actual dimensions of the unit and the location of communications. You may need to lengthen the drain hose or buy another siphon.

Checking the operation of the dishwasher

Before the first run, check:

  1. Correct connection to the mains. To do this, simply turn on the machine for a few seconds.
  2. Water supply to the unit and drain. Check all hoses for kinks and all threaded connections for leaks.
  3. Check the degree of inclination of the drain hose - ideally, water should not stagnate in the hose, unless you yourself have organized a special additional water plug to protect against unpleasant odors from the sewer.

Now, if all is well, close up all the technological holes in the walls, if any (may be necessary when laying a cable, drain hose or water supply) and put things in order in the kitchen.

How to install a dishwasher yourself (video)

Tips from the user on how to connect the dishwasher (video) - watch and remember. All connections when connecting drain and water require only manual effort - special keys are not needed for this. A minimum of tools and physical effort - and your dishwasher will start working.

Even a housewife can handle connecting a dishwasher, and there is no need to call a specialist. Just follow the sequence of operations, ensure that all materials and tools are available, and you will succeed.

In contact with

Connecting the dishwasher consists of only 4 stages: choosing the installation site, connecting the drain, cold water and electricity. Installation of each of the communications is not difficult and even a novice electrician can do it. Next, we consider a simple step by step instructions and a visual video example on how to connect the dishwasher to the water supply, sewerage and electricity.

Step 1 - Prepare tools and materials

The first thing to do after buying appliances is to prepare a set of all the necessary tools for connecting the dishwasher to communications. In addition, you should determine what consumables will be required for installation work in order to buy them in advance. For standard conditions, that is, when metal-plastic pipes with a diameter of ¾ inch are laid out around the house, as well as an electrical network with grounding, the set of materials will be as follows:

  • waste siphon with two fittings (suddenly you want to install a dishwasher in the room along with a washing machine);
  • ¾ inch tee;
  • stopcock ¾ inch;
  • deep filter (significantly extends the life of the dishwasher);
  • FUM tape;
  • socket with grounding;
  • wire of a suitable cross section and length (in case there is no outlet nearby, and you have to lead a new line from the junction box in the room).

Also, to connect a dishwasher with your own hands, you may need longer water and drain hoses. Very often, short hoses are included with the unit, which may not be available at the connection point. Here you yourself must initially measure the required length of communications from the installation site to the connection points and compare with the length of the materials included in the kit.

As for the tools, you will need the following list:

  • electric drill;
  • straight and curly screwdriver;
  • sharp knife;
  • scissors for metal-plastic pipes;
  • short building level;
  • two wrenches;
  • indicator screwdriver (determine the phase if missing).

Having prepared the entire set of tools, you can proceed to choosing the right place to install and connect the dishwasher in a private house.

Step 2 - Choose the right place

This stage, most likely, you have already fully thought out before you go and buy a product. If you have not yet decided on the location, we recommend that you consider the following nuances:

  1. The built-in option must match the dimensions of the kitchen furniture. For the dishwasher, there is a special section of the kitchen set, which allows you to install the dishwasher under the countertop, hob or even sink. You can also place the case in a closet if it is convenient for you.
  2. The distance to the sewer should not exceed 1.5 meters, otherwise the equipment pump may fail prematurely. If the dishwasher is located far from the sink and can only be installed at the edge of the kitchen, or for some reason the sewer does not go to the kitchen, consider placing the appliances in the bathroom.
  3. Choose a place in such a way that a power outlet is already installed nearby. In this case, connecting the dishwasher to the mains will be much easier.
  4. If the model is of a desktop type (as shown in the picture), you can not think over the drain system. It is enough just to fix the hose in the sink (in the kitchen there is no way without it). By the way, in this case, you can do without a siphon, besides, the pump on the drain will be completely unloaded (water will flow by gravity), which will significantly extend its service life. Installing a dishwasher on a countertop is much easier and is suitable for a small kitchen or if the furniture in the kitchen is old (not suitable by modern standards).

Having determined a suitable place, you can begin to connect the dishwasher to the sewer, water supply and electrical network. Let's consider each of the stages in more detail.

Step 3 - Connect the Water

This stage is one of the most time-consuming and the most time-consuming. First you need to shut off the water in the system, because. You will "embed" the tee into a metal-plastic pipe.

You can connect the dishwasher to the water supply as follows:

  1. We find the place of attachment of the flexible hose of the mixer to the metal-plastic pipe and disconnect it.
  2. We install the tee, having previously wound a tape on the FUM threaded connections.
  3. We wind the flexible hose of the mixer on top of the tee
  4. We connect a fine filter to the outlet, and after it there is a shut-off valve (do not forget to wind the fumka on the thread).
  5. We connect to the tap with a hose from the equipment itself.

Please note that only cold water should be used for water supply. Connecting the dishwasher to hot water is prohibited. its quality is several times worse and at the same time more electricity is spent on heating warm water than in the case of cold water!

If you do not have running water in your country house, you can still install a dishwasher. In this case, you will need to put a tank with clean water in the attic. For the operation of some models of equipment, a pressure of 0.1 MPa is sufficient (indicated in the passport), which will be created when water is supplied from a height of 2-3 meters. As you can see, you can connect the dishwasher yourself even without plumbing, if you wish. This option is often used in villages where the cold water supply is unstable.

Step 4 - Bringing the Drain

Everything is much simpler here. The best option would be to install a siphon under the sink, because. in this case, unpleasant odors from the sewer will not spread through the kitchen.

All you need to do is connect the drain circuit to the siphon, making sure that the hose is at an angle. The greater the slope, the more efficiently the water will drain (by gravity). We draw your attention to a very important nuance - at the top, at the point where the drain is connected to the siphon, it is necessary to create an inflection that will prevent water from entering the dishwasher drain from the sink (in the photo below you can see this inflection).

Step 5 - Connecting electricity

As we have already said, power should be supplied from an outlet located next to the equipment. The socket for connecting the dishwasher to the mains must be rated at least 16A and at the same time have a grounding contact.

Since the power of the dishwasher is quite high, the wiring must withstand the passing loads. To do this, you need to take care of a suitable cross-section of the wires of the wiring. It is best to implement, on the basis of which to choose the most suitable option. It is believed that for the safe operation of this type of equipment, it is necessary to use a copper core diameter of at least 2 mm. Electricity must be supplied from the junction box or the shield itself. Be sure to protect the line at 16A. Connecting a dishwasher without grounding is not allowed for electrical safety reasons. If a washing machine is already connected to the outlet, there is no need to additionally load it with a dishwasher, because. in this case, when the two devices are operating, the current overload of the outlet may occur.

Step 6 - Finishing Work

When you manage to connect all communications, all that remains is to level the equipment and carry out a control check of the installation work. As for the level, everything is quite simple here - you need to set the body according to the building level by adjusting the legs. Any distortion will negatively affect the efficiency of use and the durability of the dishwasher.

After installing and connecting the dishwasher, it remains only to check the quality of its work. To do this, you need to run a test mode in which washing takes place without dishes (idle mode). You have to watch how quickly the water fills and drains. Also, be sure to check all butt joints so that there are no leaks.

If everything is correct, then you were able to correctly install and connect the dishwasher on your own, with which we congratulate you! We recommend that you immediately view a visual video instruction that shows the installation technology of the built-in model:

Video review of installation work

For your attention a few useful tips, which will not only allow you to properly connect the dishwasher, but also extend the life of the equipment:

  • Installing a drain hose in the sink is extremely unsafe, although it greatly facilitates the connection process. The danger is that the waste water outlet can fall out of the sink and flood the neighbors from below.
  • Electrolux equipment is very demanding on installation rules. The maximum slope to one side should not exceed 2 degrees, so be sure to check this moment with a building level.
  • If you decide to buy any model from Siemens, be sure to look at the dimensions of the case and check with the standards for the manufacture of furniture in which the installation will be carried out. Very often, Siemens ignores technical standards and creates non-standard dimensions, which makes it difficult to install a dishwasher in a finished kitchen.
  • Never connect a ground contact to gas or water pipes. Grounding must be connected to the grounding bus of the apartment shield. About that, we told in a separate article.
  • The air gap between the wall and the rear wall of the equipment should be at least 5 cm, which is quite enough for air circulation.
  • The kit necessarily contains connection rules and a visual diagram for a specific model. You need to rely only on it, because. all conditions are purely individual, although they have much in common.
  • It is not recommended to use network filters (extension cords), because they are very often the cause of accidents and fires. If there is no other way to supply power, it is recommended to do it yourself. This method of connecting the dishwasher through an extension cord can be used, as an exception.
  • If you decide to put a free-standing dishwasher next to the stove, refrigerator or oven, bring a separate line from the junction box to each appliance so as not to overload the outlet installed near all devices.

Dishwasher Tips

That's the whole instruction on how to connect the dishwasher to the water supply, electricity and sewerage with your own hands. We hope that the information was useful and interesting for you. We also recommend that you familiarize yourself with so that in the future you will be familiar with how to repair equipment at home!

Technological progress is an integral part of our life. Today, the installation of a dishwasher (hereinafter - PMM, dishwasher), as well as a washing unit, is a common occurrence. Such equipment saves time and makes life easier for many people.

At the same time, buying the model you like is half the battle. In order for the unit to work flawlessly, it must be properly connected to the water supply and sewerage. Most owners can handle the independent connection of the dishwasher, you just need to follow a number of important rules. The work is carried out in several stages.

Preparatory stage

Before proceeding with the installation of the PMM, you should find a convenient place for it in the kitchen, as well as purchase the necessary tools and materials.

Where is the best place to put a dishwasher?

Certainly, the best place for automatic dishwasher - kitchen. When choosing the best accommodation option, follow these rules:

  1. If there is a place for PMM in the kitchen furniture, make sure that the built-in appliances fit in size in a niche under the countertop. If there is not enough space, you can place the unit in a closet, under the sink or in another place convenient for you.
  2. Try to choose a place near the sink, otherwise the dishwasher's drain pump will have a hard time coping with pumping water. The distance to the sewer should not exceed 1.5 meters.
  3. If there is not enough space in the kitchen, choose the desktop version of the PMM - this will automatically solve the issue with the sewerage (it will be possible to drain the water directly into the sink). Then connecting the dishwasher to the water supply and sewerage will be much easier.
  4. An electrical outlet capable of supplying electricity to the dishwasher must also be located nearby. In this case, it should be taken into account that the power of the dishwasher is usually from 2 to 3 kW.

Purchase of tools, consumables and accessories

You will need the following tools to connect:

  • electric drill and drills of different diameters;
  • flat and Phillips screwdriver;
  • hacksaw or special scissors for cutting pipes made of metal-plastic;
  • building level;
  • a set of wrenches and an adjustable wrench;
  • well-sharpened knife;
  • wire cutters.

Consumables primarily include hoses, because often those that come with equipment are not long enough. Before purchasing parts, measure the distance from the machine to the sewer and water supply. Hose clamps are additionally required.

It is possible that you will need connectors with captive nuts and fum-tape to seal the threaded connections.

In addition, you should purchase a tee and a 3/4-inch stopcock for branching from the water supply (this option is suitable if water pipes of the same diameter are routed around the house). A siphon is required to organize the drain.

In the event that a washing machine is located nearby, one siphon with two branches can be used for both units.

In the event that there is not a sufficiently powerful grounded socket nearby, to connect to the mains, purchase a three-core copper wire of a suitable cross section and the required length along with a powerful socket rated for a current of 16 A. It is best to lay the wire from the switchboard in the apartment in a separate line.

Recommendations for installing some models of dishwashers

If possible, install a compact water filter at the point of connection to the water supply - in this case, the PMM will last longer. A similar solution is recommended for Bosch dishwashers due to the fact that their inlet valves are sensitive to blockages.

When installing the filter, be careful when installing the gasket sealing the connection. Strictly follow the instructions, as the incorrect position of the part leads to leaks.

PMM Electrolux should be installed strictly according to the building level. Even a slight deviation from the horizontal position can cause the machine to not work properly.

Of all the dishwashers, one of the most unpretentious in installation and operation is the units of the Siemens brand. At the same time, built-in models require reliable fastening and strict adherence to the dimensions of niches for installation.

How to connect a dishwasher with your own hands

Self-connecting a dishwasher will save owners money and time. Read the instructions carefully before installing the dishwasher. As a rule, a short step-by-step guide is attached to all models of well-known brands. In most cases, you will have to install the PMM in four stages:

  1. Install the dishwasher in the niche and securely fasten it there.
  2. Connect a 220 V network and install a socket in the wall next to the machine body.
  3. Connect PMM to the water supply.
  4. Connect the unit to the sewer.

Power supply

It is good if, at a distance of up to 1 m from the PMM case, there is a socket with grounding in the wall, designed for a current consumption of 16 A. Then you can not do the wiring. Otherwise, you will have to call the master or supply electricity with your own hands.

For wiring, use a copper cable with three cores, the cross section of each of which must be at least 2 mm. At the entrance, in a junction box or panel, the cable must be connected to a circuit breaker rated for 16 A.

In addition, it is advisable to connect an RCD to the cable line- a residual current device rated for 16 A, with a leakage current of 30 mA (see photo).

Connecting the dishwasher to the water supply

The best option is to connect to the sink faucet located next to the PMM. To do this, turn off the cold water supply and find the place where the flexible hose from the mixer is connected to the cold water supply pipe. At this point, loosen the fastener and unscrew the nut that secures the connection of the flexible hose to the pipe, then remove the hose.

Install a tee at the connection point, the outlets of which are connected to the flexible hose of the mixer and the stopcock. Connect the coarse filter and the PMM inlet hose to the latter. Do not forget to pre-wrap the fum-sealing tape on the threads of all connections.

If you can’t connect to the plumbing under the sink, you can crash into a nearby water pipe. For cutting into metal pipe It is best to use a crimp sleeve. First, a hole must be drilled in the pipe to drain the water.

If the water pipe is made of metal-plastic, a piece equal in length to the tee to be installed must be cut out of it. Then, in the place of the cut, install a tee, to which then connect the shut-off valve, filter and PMM inlet hose.

Sewer drain preparation

In the event that the sink is located next to the dishwasher, align their drains by installing a drain siphon with an additional outlet under the sink. Water from the sink will flow through the main channel, and spent liquid with PMM will flow through the additional channel.

On sale there are options for siphons with one and two outlets. Two additional outlets are convenient when a washing machine is planned to be placed next to the dishwasher. For information on how to properly install the washing unit, read our article.

To prevent water from the siphon from entering the drain of the machine, the drain hose must be connected through a small kink connected directly to the siphon branch.

Another option is to install a tee at the entrance to the sewer, connect a kitchen sink to one of the outlets, and PMM to the other. To prevent unpleasant odors from spreading throughout the kitchen, the holes are sealed with rubber or plastic cuffs.

The easiest way is to organize a drain from a desktop PMM. To do this, just attach the drain hose to the sink sink. Particular attention should be paid to the reliability of fastening, as a hose escaping from the sink can flood the floor in the kitchen with liquid.

As you can see, it is quite possible for everyone to organize the connection of a dishwasher. You only need to have a small set of tools and improvised materials with you. If you need to embed dishwashers in a niche, follow the instructions supplied by the manufacturer with the PMM.

Fresh lemon is good for more than just tea: clean stains from the surface of an acrylic bath by rubbing with a half of cut citrus, or quickly clean the microwave by placing a container of water and lemon slices in it for 8-10 minutes at maximum power. The softened dirt will simply be wiped off with a sponge.

If the first signs of gestation in the form of untidy pellets appear on your favorite things, you can get rid of them with the help of a special machine - a shaver. It quickly and effectively shaves off clumps of fabric fibers and returns things to a decent look.

Before removing various stains from clothes, you need to find out how safe the chosen solvent is for the fabric itself. It is applied in a small amount to an inconspicuous area of ​​\u200b\u200bthe thing from the wrong side for 5-10 minutes. If the material retains its structure and color, you can move on to stains.

The threads of gold and silver, with which clothes were embroidered in the old days, are called gimp. To obtain them, the metal wire was pulled for a long time with tongs to the state of the required fineness. This is where the expression “pull (raise) the gimp” came from - “engage in long monotonous work” or “delay the execution of the case”.

In the dishwasher, not only plates and cups are washed well. It can be loaded with plastic toys, glass shades of lamps and even dirty vegetables, such as potatoes, but only without the use of detergents.

Stretch ceilings made of PVC film can withstand from 70 to 120 liters of water per 1 m 2 of its area (depending on the size of the ceiling, the degree of its tension and the quality of the film). So you can not be afraid of leaks from neighbors from above.

The easiest way to remove scale and soot from the sole of the iron is with table salt. Pour a thick layer of salt on the paper, heat the iron to the maximum and several times, pressing lightly, run the iron over the salt bedding.